Programmable Pulse Generator - Hewlett Packard 8112A Compatible

GP1612H Series – Programmable Pulse Generator – HP 8112A Compatible

Programmable Pulse Generator - Hewlett Packard 8112A Compatible
  • 50MHz frequency range with 16Vp-p into 50Ω
  • Variable width and delay with variable transitions
  • IEEE 488.2 and SCPI compatible
  • Fully compatible with the Hewlett Packard 8112A Pulse Generator


The GP1612H features variable pulse widths from 10 ns to 10 s, delays from 0 ns to10 s with up to 6 digits resolution and adjustable output levels from –8V to +8V, with pulse amplitudes from .1V to 16Vp-p into 50 ohms load (.2V to 32Vp-p into open circuit). The Pulse Generator also features selectable complementary pulse and double pulse, in continuous, triggered, gated and counted burst modes. The GP1612H allows selection of predefined amplitude and offset for critical stimulus and testing of major semiconductor technologies as TTL, CMOS and ECL.


The GP1612H has been designed to replace the HP8112A Pulse Generator and as such, is compatible with all of the HP 8112A functions and is 100% compatible in its GPIB command set. The GP1612H can replace the obsolete HP8112A in existing test and measurement systems.

Variable Transitions
To make operation flexible, variable transitions (rise and fall times) can be programmed from 5 ns to 100 ms. With the flexible transition times, various shapes of pulses can be obtained for applications where parameters such as linearity, switching times or reflection times must be analyzed. Operational amplifiers slew rate can be measured or thresholds of devices and circuits can be easily tested using programmable rise and fall times.
Fast and Easy Operation
To make operation easy, GP1612H interface with the operator in a straightforward manner by which the front panel display always shows the parameter being varied and its value. If a new parameter just entered is not compatible with the existing setup status, the operator is informed by an error message. Test setups, up to 99 locations, can be stored and recalled. This feature allows simple test sequence development as well as no need for a controller in repetitive tests, with reduced bus traffic in ATE applications. Last user setup is also retained at power down.


Automatic Test Equipment (ATE)
Avionics testing
Radar testing
HP8112A obsolescence replacement


GT90002 : GPIB Cable, Double-shielded, 1 meter

GT90003 : GPIB Cable, Double-shielded, 2 meters

GP1612H-EAR : Rack Mount Ear for GP1612H


GP1612H - Programmable Pulse Generator – Hewlett Packard 8112A Compatible

GP1612HR - HP8112 Pulse Generator Replacement Product with Rack Mount Ear


Pulse Functions
Single One pulse at each selected period up to 50MHz repetition rate
Double One pair of pulses at each period up to 25MHz repetition rate. Both pulses have the same selected width; the position of the second pulse set by the delay control.
Operating Modes
Continuous Output continuous at programmed period rate.
Triggered Output quiescent until triggered by an internal, external, GPIB or manual trigger, then generates one cycle at programmed period rate.
Gated Same as triggered mode except pulses are output for the duration of the gated signal. The last cycle started is completed
Burst Same as triggered mode for programmed number of cycles from 2 to 999,999 as set by the N-BURST function
External Width Trigger duration and rate sets pulse width and repetition
Timing Characteristics
Range 20.0 ns to 10s (50MHz to 0.1Hz repetition rate)
Resolution Up to 6 digits limited to 0.1 ns
Accuracy ±1% of setting ±1 ns.
Jitter < 0.1 % of setting +50 ps, decreasing to 0.01 % on slowest range
Range 10 ns to 9.89999 s limited by 8 ns off time
Resolution Up to 6 digits limited to 0.1 ns
Accuracy ±2% of setting ±2 ns
Jitter <(0.1% of setting + 50 pS) decreasing to 0.005% on
slowest range
Range 0 ns to 9.80000 s limited by the pulse width and 8 ns off time
Resolution Up to 6 digits limited to 0.1 ns
Accuracy ±2% of setting ±2 ns
Jitter < 0.1% of setting +50 ps, decreasing to 0.005% on slowest range
Duty Cycle
Range 1 to 99%
Resolution 3 digits (0.1%)
Accuracy Limited by width and pulse accuracy
Output Characteristics
High Level Range -7.90V to+8.00V into 50  Ω (-15.8V to +16V in open circuit)
Low Level Range -8.00V to +7.90V into 50  Ω (-16V to +15.8V in open circuit)
Amplitude Range 0.1V to 16V p-p into 50  Ω load (32V p-p max in open circuit)
Resolution 3 digits limited to 10mV
Accuracy ±1% of level setting ±2% of pk-pk amplitude 50 mV into 50 O load
Aberrations <5% + 50mV into 50  Ω load, for pulse levels between ±5V
Output Resistance 50 ohms
Transition Times
Range <5 ns to 100 ms variable. Leading and trailing edges settable separately and limited to 20:1 ratio between settings into one of the following ranges: 5ns-100ns;50ns-1.0us;500ns-10us; 5.0us-100us; 50us-1.0ms; 500us-10ms; 5ms-100ms
Resoultion 3 digits limited to 0.1 ns
Accuracy ±5% of setting ±2 ns
Linearity <5% deviation from a straight line between 10% and 90% points
Internal trigger
Range 100 nS to 99.99 s
Resolution 4 digits limited to 100 ns
Accuracy 0.01% ±1ns
Jitter <0.1 % of setting +50 ps
Inputs And Outputs Trigger Input
Sensitivity 500Vp-p minimum
Minimum Width 10ns
Maximum Rate 50 MHz
Input Impedance 1 M Ω
Input Protection ±20V DC plus peak AC
Range Selectable from -10V to +10V
Resolution 3 digits limited to 10mV
Accuracy ±5% of setting ±50 mV
Slope Selection Positive or Negative
Sync Output
A TTL level pulse at programmed period. Output impedance is 50 Ω, protected against short circuit. The high level is >2.4V into 50 Ω.
GPIB Programming
Specification IEEE-488.2
Compatibility With HP8112A GPIB command set..
Address 0-30 front panel selected
Memory Non-volatile stores up to 99 complete panel settings.
Last user setup also retained at power down.
Power Requirements 90-256V, 48-66 Hz, 70VA maximum
(Without Rack Mount Kit)
8.9 cm (3.5 in) H x 21.3 cm (8.4 in)W x 35.7 cm(14 in) L
Weight 4 kg Net
0° C to 50° C
Storage Temperature 20°C – +60°
Humidity 95% RH, 0°C to 30°C, 75% RH to 40°C, 45% RH to 50°C
Accessories 19’ rack mount kit,optional
CE Compliant Yes

Note: Specifications are subject to change without notice.

140 queries in 1.191 seconds.